Jump to content
Sign in to follow this  
You need to play a total of 1 battles to post in this section.
Smederevac94

South Dakota-class battleship (1920)

9 comments in this topic

Recommended Posts

Alpha Tester
3,237 posts
940 battles

The first South Dakota class was a class of six battleships, laid down in 1920 but never completed. They would have been the last dreadnoughts in the United States's Naval Act of 1916 to be commissioned had the Washington Naval Treaty not caused their cancellation one-third of the way through their construction. They would have been the largest, most heavily armed and armored battleships in the U.S. Navy and, designed to achieve 23 knots, represented an attempt to abandon its 21 knot standardized fleet speed and catch up with the increasing fleet speeds of its main rivals, the British Royal Navy and Imperial Japanese Navy. In this, size and secondary armament, they represented a break from the Standard-type battleship that had dominated American capital ship design for the last few ship classes, while their use of standardized bridges, lattice masts and other features was a continuation of this practice and the increase in the number of main guns from the preceding Colorado class had long been standard U.S. naval policy. The main restriction to which they had to adhere was the ability to pass through the Panama Canal.

Posted Image

The South Dakotas were authorized 4 March 1917, but work was postponed so that the U.S. Navy could incorporate information gained from the Battle of Jutland, fought in 1916, in this class's final design. Work was further postponed to give destroyers and other small fighting vessels priority as they were needed urgently to fight German U-boats in the North Atlantic. Construction started only in 1920. As the Washington Naval Treaty restricted both the total allowable battleship tonnage allowed the U.S. Navy, and limited individual ship size to 35000 tons, construction was halted 8 February 1922. While the unfinished hulls (most over 30% completed) were scrapped in 1923, the armor plates already prepared were left unused in the shipyards until World War II. The 40- and 50-ton plates intended for Montana, for instance, were sent in 1941 or 42 to the Panama Canal to reinforce the defenses and locks there. The 16" guns were transferred to the U.S. Army for use in coast artillery.

Design:

The design characteristics of the South Dakotas closely followed those of the Tennessee and Colorado classes. The increase in the number of main guns was a continuation of U.S. Navy practice from the beginning of the dreadnought era. Like the Tennessees and Colorados, they would have been fitted with standard bridges and lattice masts. Although Norman Friedman describes the South Dakotas as the ultimate development of the series of U.S. battleships that began with the Nevada class, they were also a departure in size, speed and intermediate armament from the "Standard Type" that characterized the Nevada through Colorado classes. The main restriction imposed on them by the Navy was the ability to pass through the Panama Canal. This was a policy to which capital ship designs were to strictly adhere due to the savings in time when ships needed to travel from the Pacific Ocean to the Atlantic or vice versa.

Posted Image

Posted Image

Posted Image

Propulsion:

Turbo-electric propulsion, which the U.S. Navy had adopted for capital ships with the New Mexico-class battleships, was continued in this class. This circumvented one potential bottleneck since American companies struggled to produce the very large reduction gears necessary for such big ships. The separate turbine normally needed to steam astern could be eliminated since the direction of rotation could simply be reversed by means of the commutators, which ensured rapid changeover. The turbines could run at their optimum speed, without regard to propeller speed, which was economical on fuel. The machinery could also be subdivided more tightly, which could increase the ships' ability to withstand torpedo hits. On the down side, the machinery was heavier and bulkier than geared turbines. There was the danger of high voltage to the crew. Also, despite elaborate attempts at insulation, protection against moisture damage or flooding (from battle damage and other causes) remained inadequate.

In the South Dakotas, two turbo generators (General Electric for Indiana and Montana, Westinghouse for the others) would have been coupled to two AC alternators of 28,000 KVA and 5000 volts. These would feed four electric motors, one per propeller shaft, each rated at 11,200 kilowatts (15,000 hp) of direct current (DC). Sixteen water-tube boilers, each in their own individual compartment, would have lined the turbine rooms to provide steam for the generators. With a total of 60000 electrical horsepower (EHP), top speed was expected to be 23 knots.

Armament:

Main guns

The South Dakotas were slated to carry carried twelve 16-inch 50 caliber Mark 2 guns in four triple turrets. These fired the same 2,100-pound (950 kg) shell as the Mark 1 of the Colorado class with a muzzle velocity of 2,650 feet per second (810 m/s) to an effective range of 44,600 yards (40,800 m). at a maximum elevation of 46 degrees. The Mark 2 was not fitted on any ship; the 16"/50s used later on the Iowa-class battleships were of a lighter design, the Mark 7. With the cancellation of the South Dakotas and Lexingtons, the existing guns were transferred to the Army and installed in coastal defense batteries in place of the Army's more massive and much more expensive M1919 16-inch Coast Gun.

Posted Image

16"/50 caliber Mark 2 Gun

Secondary guns

Secondary armament would have been sixteen 6-inch (150 mm) 53 caliber guns. Twelve of these were to be on Mark 13 mountings in unarmored casemates; the rest would have been placed open on the superstructure deck. This was a departure from the 5-inch (130 mm) 51 caliber guns used in U.S. battleships since the Florida class of 1908. The 6"/53 fired a 105-pound (47.6 kg) projectile a velocity of 3,000 feet per second (900 m/s) to a maximum range of 21,000 yd (19,000 m) at a maximum elevation of 20 degrees. They were installed in Omaha-class cruisers when the South Dakotas were canceled under the Washington Naval Treaty and would become a mainstay of U.S. Navy light cruisers and submarine cruisers built during the 1920s.

Posted Image

6"/53 caliber naval gun

Armor:

According to Siegfreid Breyer, the protective system of the South Dakotas was designed to be 50 percent stronger than that of HMS Hood. Belt armor was a consistent 13.5 inches (340 mm), not tapered. The upper armored deck, 2.5–3.5 inches (64–89 mm) thick, rested on the top edge of the belt armor. One deck below this was a second armored belt, 1.5–2.5 inches (38–64 mm). Fore and aft transverse armored bulkheads of 13.5 inches (340 mm) sealed off the machinery and magazines. Past these, the lower armored deck continued at a thickness of 6 inches (150 mm) to the ends of the ship. Forward, above this, the upper armored deck continued at a thickness of 3.5 inches (89 mm). Flue gas exits were armored for one deck upwards from the upper armored deck at a thickness of 13.5 inches (340 mm).

Protection for the main guns was also considerable. Barbettes were 13.5 inches (340 mm) above the upper armored deck and 5.5 inches (140 mm) from there to the lower armored deck. Turret rings were also armored to a thickness of 13.5 inches (340 mm). Turret faces were 18 in (457 mm), sides 9–10 inches (230–250 mm), top 5 inches (130 mm) and rear 9 inches (230 mm). Conning tower armor was 16 in (406 mm) on the front and sides, 8 inches (200 mm) on top. Underwater protection was more subdivided longitudinally than in the Colorados but was otherwise similar, with three armored bulkheads .75 inches (19 mm) thick from the lower armored deck to the ship's bottom to the armored transverse bulkheads near the ends.

For more images go here:

http://www.navsource...hives/01/49.htm

 

Displacement: 43,200 tons standard / 47,000 tons full

 

Length:  684 ft (208 m)

 

Beam:  105 ft (32 m)

 

Draft: 33 ft (10 m)

 

Speed: 23 knots (43 km/h)

 

Armament:

12 × 16-inch/50 caliber guns (4×3)

16 × 6-inch/53 caliber guns

4 × 3-inch/50 caliber guns

2 × 21-inch torpedo tubes

 

Armor:

Belt: 8–13.5 in (203–343 mm)

Barbettes: 13 in (330 mm)

Turret face: 18 in (457 mm)

Turret sides: 9–10 in (229–254 mm)

Turret top: 5 in (127 mm)

Turret rear: 9 in (229 mm)

Conning tower: 11.5 in (292 mm)

Decks: 3.5 in (89 mm)

Share this post


Link to post
Share on other sites
Alpha Tester, In AlfaTesters
1,623 posts
1,187 battles

Good post but for me are two pictures broken.

Share this post


Link to post
Share on other sites
Alpha Tester
3,237 posts
940 battles

View PostJann336, on 01 May 2013 - 07:25 PM, said:

Good post but for me are two pictures broken.
Realy???I see all the pictures,I do not know what the problem is, sry for that two pics.

Share this post


Link to post
Share on other sites
Alpha Tester, In AlfaTesters
1,623 posts
1,187 battles

View PostSmederevac94, on 01 May 2013 - 07:49 PM, said:

Realy???I see all the pictures,I do not know what the problem is, sry for that two pics.

No problem.

Share this post


Link to post
Share on other sites
Alpha Tester
3,768 posts
58 battles

But they weren't actually made so comparing them to what the Germans did make is invalid.

Share this post


Link to post
Share on other sites
Alpha Tester
3,237 posts
940 battles

View PostBloodhound79, on 11 May 2013 - 03:46 PM, said:

yes nice post but for me also the second and foruth pictures are broken links
There is something wrong with the forum.

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

  • Recently Browsing   0 members

    No registered users viewing this page.

×